silicon epitaxial planar diode semelab limited reserves the right to change test c onditions, parameter limits and package dimensions without notice. information furnished by semelab is believed to be both accurate and reliable at the time of going to press. however semelab assumes no responsibility for any errors or omissions discovered in its use. semelab encourage s customers to verify that datasheets are current before placing o rders. semelab limited semelab limited semelab limited semelab limited coventry road, lutterworth, leicestershire, le17 4 jb telephone +44 (0) 1455 556565 fax +44 (0) 1455 5526 12 email: sales@semelab-tt.com website: http://www.semelab-tt.com document number 7789 issue 2 page 1 of 4 1n4148csm ? low leakage ? fast switching ? low forward voltage ? hermetic ceramic surface mount package ? suitable for general purpose, switching application s. ? screening options available absolute maximum ratings (t a = 25c unless otherwise stated) v br breakdown voltage 100v v rwm working peak reverse voltage 75v i o (1) average rectified output current, t a = 75c 200ma i fsm surge current, half sine wave, t p = 8.3ms 2a p d (1) total power dissipation at t a = 75c 385mw derate above 75c 3.08mw/c p d total power dissipation at t sp = 75c 1.042w derate above 75c 8.33mw/c t j junction temperature range -65 to +200c t stg storage temperature range -65 to +200c thermal properties symbols parameters min. typ. max. units r ja (pcb) (1) thermal resistance, junction to ambient, on pcb 325 c/w r jsp thermal resistance, junction to solder pads 120 c/w notes notes notes notes (1) pcb = fr4 ? 0.0625 inch (1.59mm), 1 layer, 1.0-oz c u, horizontal, in still air. r ja with a defined pcb thermal resistance condition in cluded, is measured at i o = 200ma.
silicon epitaxial planar diode 1n4148csm semelab limited semelab limited semelab limited semelab limited coventry road, lutterworth, leicestershire, le17 4 jb telephone +44 (0) 1455 556565 fax +44 (0) 1455 5526 12 email: sales@semelab-tt.com website: http://www.semelab-tt.com document number 7789 issue 2 page 2 of 4 electrical characteristics (t a = 25c unless otherwise stated) symbols parameters test conditions min. typ max. units v br breakdown voltage i r = 100a 100 i f = 10ma 0.8 i f = 100ma 1.2 i f = 10ma t a = 150c 0.8 v f (2) forward voltage i f = 100ma t a = -55c 1.3 v v r = 20v 25 v r = 75v 500 na v r = 20v 35 i r reverse current v r = 75v t a = 150c 75 a dynamic characteristics v r = 0v 4 c capacitance v r = 1.5v f = 1.0mhz 2.8 pf i f = ir = 10ma r l = 100 t rr reverse recovery time i rec = 1.0ma 5 ns notes notes notes notes (2) pulse width 300us, 2%
silicon epitaxial planar diode 1n4148csm semelab limited semelab limited semelab limited semelab limited coventry road, lutterworth, leicestershire, le17 4 jb telephone +44 (0) 1455 556565 fax +44 (0) 1455 5526 12 email: sales@semelab-tt.com website: http://www.semelab-tt.com document number 7789 issue 2 page 3 of 4 mechanical data dimensions in mm (inches) * the additional contact provides a connection to t he lid in the application. connecting the metal lid to a known electrical potential stops deep dielectric discharge in space applications; see the space weather link www.semelab.co.uk/mil/lcc1_4 on the semelab web site. package variant to be specified at order. other package outlines may be available ? contact s emelab sales to enquire 2 1 0.51 0.10 (0.02 0.004) r0.31 (0.012) 1.91 0.10 (0.075 0.004) 3.05 0.13 (0.12 0.005) 2.54 0.13 (0.10 0.005) 0.76 0.15 (0.03 0.006) 1.40 (0.055) max. 0.31 (0.012) rad. 3 1.02 0.10 (0.04 0.004) 2 1 0.51 0.10 (0.02 0.004) 1.91 0.10 (0.075 0.004) 3.05 0.13 (0.12 0.005) 2.54 0.13 (0.10 0.005) 0.76 0.15 (0.03 0.006) 1.40 (0.055) max. 0.31 (0.012) rad. r0.31 (0.012) 3 1.02 0.10 (0.04 0.004) 4 r0 .5 6 ( 0.0 22 ) lcc1 (underside view) pad 1 - anode pad 2 ? n/c pad 3 - cathode lcc1 - 4 (underside view) pad 1 - anode pad 2 ? n/c pad 3 ? cathode pad 4 ?lid co ntact ground * note: if required, must be request note: if required, must be request note: if required, must be request note: if required, must be requested eded ed at time of order at time of order at time of order at time of order
silicon epitaxial planar diode 1n4148csm semelab limited semelab limited semelab limited semelab limited coventry road, lutterworth, leicestershire, le17 4 jb telephone +44 (0) 1455 556565 fax +44 (0) 1455 5526 12 email: sales@semelab-tt.com website: http://www.semelab-tt.com document number 7789 issue 2 page 4 of 4 screening options space level (jqrs/esa) and high reliability options a re available in accordance with the high reliability and screening options handbook available for download from the from the tt electronics semelab web site. esa quality level products are based on the testing procedures specified in the generic escc 5000 and in the corresponding part detail specifications. semelabs qr216 and qr217 processing specifications (jqrs), in conjunction with the companies iso 9001: 2000 approval present a viable alternative to the america n mil- prf-19500 space level processing. qr217 (space level quality conformance) is based on the quality conformance inspection requirements of mil- prf- 19500 groups a (table v), b (table via), c (table vi i) and also esa / escc 5000 (chart f4) lot validation tests. qr216 (space level screening) is based on the scree ning requirements of mil-prf-19500 (table iv) and also e sa /escc 5000 (chart f3). jqrs parts are processed to the device data sheet a nd screened to qr216 with conformance testing to q217 groups a and b in accordance with mil-std-750 method s and procedures. additional conformance options are available, for ex ample pre-cap visual inspection, buy-off visit or data pac ks. these are chargeable and must be specified at the o rder stage (see ordering information). minimum order quantities may apply. alternative or additional customer specific conforma nce or screening requirements would be considered. contact semelab sales with enquires. marking details screened parts are typically marked with specificat ion number, serial number (or week of seal) as shown in the example below. all non screened parts are printed wi th three characters only eg. 148. customer specific marking requirements can be arrang ed at time of order but is approximately limited to two l ines of 7 characters. this is to ensure text remains readabl e.. example marking: ordering information part number is built from part and screening level. the part number can be extended to include the additional op tions as shown below. type ? see electrical stability characteristics tab le package variant ? see mechanical data screening level ? see screening options (esa / jqrs) additional options: customer pre-cap visual inspection .cvp customer buy-off visit .cvb data pack .da solderability samples .ss scanning electron microscopy .sem radiography (x-ray) .xray total dose radiation test .rad mil-prf-19500 (qr217) group b charge .grpb group b destructive mechanical samples .gbdm (12 pi eces) group c charge .grpc group c destructive electrical samples .gcde (12 pi eces) group c destructive mechanical samples .gcdm (6 pie ces) esa/escc lot validation testing (subgroup 1) charge .lvt1 lvt1 destructive samples (environmental) .l1de (15 pieces) lvt1 destructive samples (mechanical) .l1dm (15 pie ces) lot validation testing (subgroup 2) charge .lvt2 lvt2 endurance samples (electrical) .l2d (15 pieces ) lot validation testing (subgroup 3) charge .lvt3 lvt3 destructive samples (mechanical) .l3d (5 piece s) additional option notes: 1) all ?additional options? are chargeable and must be specified at order stage. 2) when group b,c or lvt is required, additional el ectrical and mechanical destructive samples must be ordered 3) all destructive samples are marked the same as o ther production parts unless otherwise requested. example ordering information: the following example is for the part with, jqrs sc reening, additional group c conformance testing and a data pac k. part numbers: 1n4148csm-jqrs (include quantity for flight parts) 1n4148csm-jqrs.grpc (chargeable conformance option) 1n4148csm-jqrs.gcde (charge for destructive parts) 1n4148csm-jqrs.gcdm (charge for destructive parts) 1n4148csm-jqrs.da (charge for data pack) customers with any specific requirements (e.g. marki ng, package or screening) may be supplied with a simila r alternative part number (there is maximum 20 charac ter limit to part numbers). requirements for deep diele ctric discharge variant (lcc1-4) must be specified at time of order. contact semelab sales with all enquiries high reliability and screening options handbook link : http://www.semelab.co.uk/pdf/misc/documents/hirel_ and_screening_options.pdf
|
